Handlebar Risers with Offset for BMW R 1250 R


All Bikes


Handlebar risers with offset: 30mm higher and 21mm closer to the rider

Raising the handlebar by 30mm results in a more upright, much more relaxed seating position. Moreover, the handlebar is brought 21mm closer to the rider which additionally improves driving comfort. The overall result is a noticeable increase in stamina and concentration. Long stretches on the motorway are less nerve-racking.
Fits on original 32mm handlebar.
Also referred to as handlebar risers, handlebar height increase, bar back risers, barbacks.

BMW R1250R

Install Instruction

When mounting the handlebar risers, you have to reposition the clutch cable (see install instruction).
If repositioning the clutch cable is too complex, you can also extend it with our special adapter (part no. 26865), which is sold separately.
Install Instruction Extension Adapter for Clutch Cable
Example video installation instruction for the extension adapter for the clutch cable

If the original brake line is too short or tensioned after mounting the handlebar risers, the brake line can be extended with our special adapter (item no. 26860), which is sold separately.
Install Instruction Extension Adapter for brake line


Handlebar Risers 30/21mm

Article-No. : 26206

Availability: immediately available    Show details
Price: € 102,90
USD: 109,84 $
GBP: 88,55 £
AUD: 170,16 $A

without VAT plus shipping

Adapter for clutch cable
Fits for R1200GS & Adv LC, R1250GS & Adv, R1200RT LC, R1250RT, R1200R LC, R1250R, R1200RS, R1250RS, RnineT (2013-2016), K1600GT & GTL (2016-), K1600B

Article-No. : 26865

Availability: immediately available    Show details
Price: € 39,90
USD: 42,59 $
GBP: 34,33 £
AUD: 65,98 $A

without VAT plus shipping

Adapter for brake line
Fits for R1200GS & Adv LC, R1250GS & Adv, R1200RT LC, R1250RT, R1200R LC, R1250R, R1200RS, R1250RS, RnineT (2013-2016)

Article-No. : 26860

Availability: immediately available    Show details
Price: € 39,90
USD: 42,59 $
GBP: 34,33 £
AUD: 65,98 $A

without VAT plus shipping

4 pieces stainless steel Allen screw M8 for replacing the special screws

Article-No. : 2534-520

Availability: immediately available    Show details
Price: € 11,90
USD: 12,70 $
GBP: 10,24 £
AUD: 19,68 $A

without VAT plus shipping

Questions about this article


Are special bolt available for the 30/21 riser to accommodate the r1250r NAV mounting as with the smaller 25 mm riser?
Yes, we offer the special Screws set 31002 to mount the BMW GPS System on a usual Handlebar riser without offset (25mm). If you use our special Screws set you do not need to remove your GPS.

We do not offer the same special Screw set to mount the GPS on a Handlebar riser with offset. On this handlebar riser the original BMW GPS system fits without any change.
But we offer a special set of screws 2534-520 for the handlebar riser with offset, which can replace your special Screws in case you want to remove your GPS.

Why can I not pull the clutch line as it is shown in the video / in the installation instruction?
The clutch line is fixed at the frame (behind the cooler) with a clamp (hose holder). You cannot see this clamp, you can only feel it when you grab along the clutch line with your hand. The holder must be opened and only then you can pull the clutch line (as shown in the video / installation instruction).


Do I need the additional screws (item 2534-520)?
BMW uses special screws with threads in their extended screw heads on the triple clamp in order to mount the navigation system there. If somebody does not want to mount the navigation system there anylonger, our shorter screws (2534-520) can be used. With these screws you do not have any disturbing screw heads with thread on the triple clamp. An elegant solution if you do not want to mount the support of the BMW GPS system on the triple clamp anylonger. Our short screws (2534-520) are not necessary for mounting the handlebar risers.

Ratings

Rating:
The average rating of this product is 5 of 5:
(after 4 Ratings)
Rating
Ole. S. wrote | 2024-04-22:
Very good
Rating

Conrad wrote | 2022-07-21:
Top quality product. Even came in a nice box. Highly recommend.
Rating

Brett F. wrote | 2020-09-04:
This is a nice product, Very happy with it. Well made and finished, with careful re- routing of the clutch hose it fitted perfectly. ( Mechanical ability required ) The difference in ride is subtle but effective, I would definitely recommend this product, definitely improved comfort on the bike for me.
Rating

Show all Make a new evaluation


Related / Recommended Products


Adjustable Gear Lever

The adjustable gear lever for the BMW R1250R is made of...

Price € 140,00
without VAT plus shipping

Cover brake fluid reservoir

Cover for the brake fluid reservoir. Honed from top grade...

Price € 32,90
without VAT plus shipping

Stainless steel crash bars

Our stainless steel engine guards will never rust like...

Price € 439,90
without VAT plus shipping